MaxPower CT60 Guia de Resolução de Problemas Página 4
- Página / 22
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
English Manual: Super Power Series 60-80 25/03/2004
3
Fit the tunnel and mark the areas to be fibre-glassed. Sand these areas inside and out.
In certain installations it is preferable to drill the position of the thruster support before the
installation of the tunnel.
Refit the tunnel. Apply reinforced fibreglass filler to all areas, taking care that you fill the gap
between hull and tunnel. Stratify with a minimum of 8 coats of material and ISOPHTALIQUE
RESINE alternating with mat and roving.
In the areas not accessible (i.e. under the tunnel), it is possible to apply simply reinforced filler.
DO NOT FIBREGLASS THE AREA OF THE MOTOR SUPPORT.
It is recommended to lightly sand down the area where the electric motor is fitted.
On the outside, when the ISOPHTALIQUE RESIN has set, finish with an application of resin
and material, followed with an additional coat on the hull, in the tunnel area.
To optimise the flow of water while sailing, deflectors & a relief should be fashioned.
These can be made up with several coats of reinforced filler in order to obtain the required
hydrodynamic lines.
Relief
Deflector
Once all fibreglass work is complete, apply a coat of epoxy or gel-coat to waterproof the
entire area.
3 PROPELLER DRIVE LEG & MOTOR SUPPORT
The leg’s gasket and the motor‘s support can be used to mark up the drilling position, in
some cases it might be easier, to mark out the position, and drill before the stratification of
the tunnel.
Centre and trace the drilling positions for the leg and its support.
Fit the leg along with the gasket, in the tunnel.
Check general positioning of the propellers.
Small pieces of folded cardboard can be used to check the spacing between the propeller tips
and the tunnel is even all round. Slight adjustment to align the leg in its tunnel may be
necessary.
After checks, remove leg etc, remount the assembly, covering the gasket with a jointing
compound resistant to oil, salt water, et after fitting, remove all access compound.
The gasket must be between the leg and the tunnel, and not between the motor support and
the tunnel.
Care must be taken at all times when fitting the leg into the motor support to ensure that
the mating components are dirt free and covered with a light film of grease. (IMPORTANT:
GRAPHITE GREASE MUST NOT BE USED).
Torque values: screw Ø 8 mm = 30 Nm screw, tighten the two fixing screws alternately.
Once tightened, ensure that the propeller/s turn freely without touching the tunnel.
- Electric Tunnel Thruster 1
- 12V 24V 1
- Table of Contents 2
- As far forward as possible 3
- Deflector 4
- Positive 6
- Negative 6
- Single Touch Panel: 7
- Single Joystick Panel: 7
- Double Joystick Panel: 7
- Power Connections 8
- 60 MONO composite 12
- 80 DUO composite 12
- 80 DUO classic 12
- DUO classic 12
- 25/03/2004 13
- PWRISOPNL 15
- HEAT RLYS 15
- TROUBLE SHOOTING GUIDE 16
- WARRANTY COVERAGE 18
- DISTRIBUTOR CONTACT LIST 20
- AMERICAS 21
- WARRANTY FORM 22
Manuais e produtos relacionados com não MaxPower CT60
não MaxPower CT60 Guia de Resolução de Problemas
(19 páginas)
(19 páginas)
Heath Zenith Motion sensing Pendant Light 4350 manuali
Manuali dei proprietari e guide per l'utente per Proiettori Heath Zenith Motion sensing Pendant Light 4350.
We fornisce 1 manuali pdf Heath Zenith Motion sensing Pendant Light 4350 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Comentários a estes Manuais